![]() If you decide to use privacy the select Auth_Priv as PeakHour's Security Mode. Here you get the choice of auth protocol, MD5 or SHA, and enabling privacy (which the SNMP client optionally uses, or not) with DES or AES privacy protocol. Or this: View attachment 3714 View attachment 3715 This: View attachment 3712 View attachment 3713 The first question is this: are you running PeakHour 4 v4.1.14? And is it's app icon and Preferences toolbar. If you decide to use privacy then select Auth+Priv as PeakHour's Security Mode. ![]() I monitor four interfaces (so four PeakHour 'devices'), my best guesses were: Auth Key: the router's SNMP password you used.Security Name: the router's SNMP username you used.Enter username and password you want for this device.SRM -> Control Panel -> Services -> System Services They acknowledged this and provided the corrected version, with the normal round icon, and is now available from their website via the Trial button. I found this one didn't work with any of my previously working SNMP sources. This will be a fairly complex network to manage and maintain, and giving Internet access to the 192.168.1.128/128 network and 192.168.1.0/128 networks will require configuring some device to NAT for them.The reason I ask is that the v4.1.14 with square icon was apparently released accidentally. You can do this with static routes or using a dynamic routing protocol like OSPF. For example, routers A and B would need a route to 192.168.1.128/128 through 192.168.9.3 so they know to forward traffic to hosts on that subnet to router C. The 192.168.9.0/24 network services to interconnect the routers.įor this to work, however, you would need all three routers to understand how to route to all the networks involved. That creates a new network to connect the three routers and you could assign router B the address 192.168.9.2/24 on that network and router C can be 192.168.9.3/24 on that network. For example, you could configure router A's LAN side to 192.168.9.1/24. Instead, change router A's LAN side to something else. If you want to have two subnets, 192.168.1.0/25 and 192.168.1.128/25 then you don't want a physical network numbered 192.168.1.0/24 because that would include both blocks in the same physical network. If you want to two devices to connect to each other without a router between them, they should be on the same network. You don't subnet a network, you subnet a network block. But as you can use the whole private address space, you can also use 192.168.2.0/24 for your second subnet. You can have one subnet 192.168.1.0/25, this includes the addresses from 192.168.0.0 to 192.168.0.127, although the lowest and the highest address are not used. Regarding subnets, the only requirement is that they don't contain public addresses and that they are distinct. You can also reverse the configuration, but without additional blocking, devices in the second router have access to devices on the main router. If you want just a guest Wifi, You can also get a simple router, use the manufacturer's NAT configuration, connect your devices to the new router and the router together with the guests to the main router. You can setup iptables to allow or deny access between the networks as you like. You can connect your second router to the main router and have two subnets behind the second router. With an additional router, you can split your internal network in two, one part between the main router and the second router, the other part behind the second router. You could also see whether you can run OpenWRT on your main router, but I don' recommend that, if you misconfigure your router, you won't be able to search the internet for help. Most home routers already run a Linux system, but it is usually locked down by the vendor and less flexible. Once you’re in, create a new password and username. These details should be provided in the router’s manual. At this point, log into your account using the router’s default admin name and password. OpenWRT is a Linux system designed for routers. Most routers come with an app or web dashboard to help you continue to configure your router. If you want to experiment and learn, I recommend getting a cheap router that is supported by OpenWRT. If you want two networks, there is no need for three routers, also no obvious benefit. A router is a device that connects two or more networks.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |